The Complete Guide To Fiat Panda Key Fob Replacement

Reasons Your fiat van key replacement 500 Key Fob Won't Work

A fiat 500 key fob is a convenient method to open the doors and start the car. However, there are numerous reasons the fob could stop functioning. This could be due to a dead coin battery damage to the receiver module, water problems, and interference.

This listing is for a NEW replacement Fiat Flip Key Remote that is similar to the Ilco brand. It must be professionally programmed (click here to find local locksmiths for automotive locksmiths). It comes with trunk, lock and unlock buttons.

Dead Coin Battery

The most common reason the 500 key fob won't work is a dead battery. Modern key fobs have a restricted operating range, and must be within just a few feet of the vehicle in order to function. If you are far from your vehicle and you press the keyfob button it won't respond and display the message "Key Fob Not Detected".

If this happens, replace the battery on your coin cell (Part number CR2032) with a brand new one from a trusted brand like Panasonic, Duracell, or Energizer. They are usually available at your local hardware store, or online.

You can test the coin-cell battery by pressing the buttons while standing near your fiat doblo van remote key 500. The parking lights should light up and the key fob should operate the lock and unlock switches.

If the fob's key doesn't function after replacing the battery, it may be damaged by water, which prevents it from communicating with the receiver module in your car. Water damage can occur in a variety of ways, ranging from a light splash to submerging your fob in salt water at the beach. If you suspect your fob has been exposed to water, put it in a dry rice bag to draw the moisture out. If this doesn't work, your fob is likely to require reprogramming by a professional locksmith or dealer.

Water Damage

Damage to the water supply can occur if you immerse the fob in the ocean, or wash it in a washer. Saltwater can cause the circuit board to short and eventually cease to function. In the event that you let your fob get wet, it's not an ideal choice but if you accidentally drop it into the water in a cup or do not remember to remove it from your pocket before you run the washing machine Don't give up hope.

First, remove the battery from the fob. Before replacing the battery, clean the electronic chip using isopropyl or a similar product. Then try the fob and verify if it is working. If the key isn't working, it may need to be reset. This is usually handled by an auto locksmith or dealer.

If the key is more recent and has never been programmed to your vehicle It is likely that it needs to be replaced completely. This is a simple process that can be completed by a professional locksmith for automotive use. The locksmith will require the key to be cut to match your vehicle's ignition. The locksmith also needs to program your fob into the vehicle's system. This is a fast and affordable process that is usually completed on the same day.

Receiver Module Issues

Your 500 key fob may not function because it's out of range. The remote has a maximum range of 30 feet. So in the event that you are far away from your vehicle it won't respond to your commands. It's easy to remedy this by moving your remote closer to your vehicle until it responds.

If you've replaced your coin battery (commonly known as a "button" or "watch") and Programming the fob won't work It could be because of an internal circuit board problem. In most cases, reprogramming the fob will fix the problem. You can find the instructions on how to start a fiat 500x with key to do this for most automobiles by searching YouTube or checking out the owner's manual.

It's possible that you need to replace the metal clips that keep the coin battery in place. If they loose tension it can prevent the coin battery from being properly seated, and this will cause the remote to malfunction.

In rare instances, the fob may be out of alignment with your vehicle because of hardware or software problems. This issue can be fixed by visiting your local auto-locksmith or dealer to reprogram your key fob. In certain instances they might need to reinstall the software in your body control module, as well.

Interference

In addition to a dead battery on a coin, the key fob may not be receiving or transmitting signals due to interference. This could occur if the key fob is near a radio transmitter (cell phones or radar detectors) or any other source of electromagnetic radiation. The key fob could not function due to a bad connection with the buttons water damage or damage to the internal chips.

If your key fob suddenly stopped working, or if you've tried everything at home to solve the issue (e.g. battery replacement, reprogramming and using the spare key fob, you might have a faulty receiver module on your 500. The receiver module, which is located beneath the dashboard, is able to pick up radio frequency signals from your key fob. Then, it converts them into electronic commands that the vehicle interprets.

Luckily, there is an easy method of resetting all of the on-board systems in your 500 keys, including the key fob. Disconnect the battery for 15 minutes by removing first the negative cable, then the positive cable. Reconnect the battery. This will get rid of any remaining electricity and then restart the car's computers, which could allow you to get your key fob working again. If the problem persists you should seek the advice of an expert technician. They'll be able identify the root cause of your problem.