How To Explain Fiat Panda Key Fob Replacement To A Five-Year-Old

Reasons Your fiat replacement car keys 500 Key Fob Won't Work

A key fob from Fiat 500 is a convenient method to open the doors and start the car. There are a myriad of reasons why the fob may stop functioning. This includes a dead coin-battery water damage, issues with the receiver module, and interference.

This listing is for a NEW replacement fiat punto keys stilo key (visit this hyperlink) Flip Key Remote - look-alike Ilco brand that must be professionally programmed by a local automotive locksmith (click here to search for a Locksmith Search). It comes with trunk, lock and unlock buttons.

Dead Coin Battery

A dead battery is probably the most common reason for your 500 key fob being inoperative. Modern key fobs have an operating range that is limited and must be within only a few inches from the vehicle in order to function. If you are further away from your vehicle and you push the keyfob button it will not respond, and display the message "Key Fob Not Detected".

If this happens, simply replace the coin cell battery (Part number CR2032) with a brand new one from a trusted brand such as Panasonic, Duracell, or Energizer. You can usually find them at your local hardware store or on the internet.

You can test the battery on your coin-cell by pressing the buttons while you're standing close to your fiat key fob replacement 500. The parking lights will flash and the key fob should operate the lock and unlock switch.

If the fob's remote doesn't function after replacing the battery, it might have water damage that prevents it from communicating with the receiver module in your vehicle. Water damage can occur through a variety of methods, including simply splashing or submerging the key fob saltwater at the beach. If you suspect that your fob was exposed to water, you can try placing it in a dry rice bag to pull the moisture back out. If this doesn't work your fob will probably require reprogramming by an experienced auto locksmith or by the dealer.

Water Damage

While the fob has some rubber seals that keep water from the electronic chip inside the device, submerging it into the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to short, and eventually fail. The fob getting wet is not an ideal choice however, if you drop it in a cup of water or fail to remove it from your pants pocket prior to running the washer do not give up hope.

First, remove the battery from the fob. Clean the electronic chip with isopropyl or a similar product and then dry it thoroughly before replacing the battery. Next test the fob to verify if it is working. If the fob doesn't function, it may need to be reset. This is typically handled by a professional or dealer auto locksmith.

If your key is a bit older and not programmed to work with your vehicle You will need to replace it completely. A professional automotive locksmith can carry out this simple task. The locksmith will need the key cut to match your car's ignition. The locksmith will also have to reprogram the fob into the vehicle's system. This is a cost-effective and quick process that could be completed the same day.

Receiver Module Issues

The 500 key fob could stop working because it is out of range. The remote has a range of 30 feet. Therefore, should you be too far away from your vehicle it won't be able to respond to your commands. It's easy to fix this by moving the remote closer to your car until it responds.

If you've replaced the battery in your coin (commonly known as"button" or "button" or "watch") and the fob won't work it could be due to an internal circuit board issue. In the majority of cases, reprogramming your fob will resolve this problem. There are instructions on how to do this for all automobiles by searching YouTube or checking out the owner's manual.

It is sometimes necessary to replace the metal clips that hold the coin batteries in place. If they loose tension it could hinder the battery from being seated properly and could result in the malfunction of your remote.

In rare cases it is possible that the fob will become disconnected from your vehicle due to software problems or hardware issues. This could be a huge headache, but you can frequently fix this issue by visiting an auto locksmith to have them reprogram your fob. In certain instances the software may require reinstallation in your body control modules.

Interference

In addition to a dead coin battery, the key fob may not be able to receive or transmit an signal due to interference. This could happen if the key fob is close to radio transmitters (cell phones or radar detectors) or another source of electromagnetic radiation. The key fob may not work because of a problem with the buttons or water damage, or damage to the internal chips.

If the key fob failed to work one day out of the blue and you've tried everything you can at home to resolve it e.g. replacing the battery, reprogramming, and using the spare key fob, it could have a damaged receiver module on your 500. The receiver module, which is located beneath the dashboard, receives radio frequency signals from your key fob. It transforms the signals into electronic commands, which are then processed by the vehicle.

There is a straightforward method to reset the 500's in-board system including the keyfob. Disconnect the 12 volt battery for about 15 minutes by removing the negative cable first then the positive cable. Then, reconnect the battery. This will clear out any remaining electricity and then restart the car's computer system, which could allow you to the key fob to function again. If the issue persists, you should seek out an expert technician. They'll be able identify the root cause of your issues.