What Is Saab 9-3 Key Replacement And Why Is Everyone Dissing It?

How to Replace the Replacement Key Battery For the saab 9-3 key fob programming 9-3

saab 93 key replacement owners have to follow a series of special steps to install a second ignition key. This requires an electronic handheld computer, referred to as Tech-2, to be used by the dealer. Then a new car key and transponder need to be bought and programmed to the car.

It is recommended to rotate your keys so that one does not wear out faster than the other. This will help keep your keys in top condition.

Replacement Case

In contrast to the traditional Saab keys of the past, the new keys have electronic components that make it difficult to duplicate. This has made stealing cars considerably more difficult than it was twenty years ago. However, it also has made replacing lost keys a more expensive undertaking.

Every owner of a Saab 9-3 needs to have at least two working keys. If one of them is lost, it costs a fortune to replace it in the car since it requires replacing the CIM module and programming the locking cylinders. Dealers usually charge between $100 and $200 to complete this.

There are ways to avoid these high costs. Some parts suppliers will use the code of the spare key to cut a brand new metal blade for less than what the dealer charges. The key must be exactly the same as the original to allow it to function in your vehicle.

Follow these steps to replace the case. You will need to have an open-faced screwdriver and a lot of patience. With the screwdriver, pry apart the plastic, and then take off the emergency key. After the case is open remove all electronics and put them back in your new case. Make sure you insert the correct badge and key back inside the case, too.

Replacement Battery

The Saab 9-3 replacement battery is an inexpensive component that can be quickly and easily replaced. This DIY video from YouTube user Cyclone Cyd explains how to replace the remote key fob battery in only four steps. This tutorial is suitable for any modern saab key fob, though the process may vary slightly.

The button is normally located close to the Saab logo on the back of the fob. The button is usually found on the back of your fob, next to the Saab Logo. Then take the flathead screwdriver to insert into the tiny hole in this button. This should be enough to let the fob case open so that you can change the battery.

After the new battery CR1632 is in place You can then reassemble the remote key fob and program it to your car. The whole process should take more than a half hour at the most. It is a simple procedure that doesn't require any special tools.

The process can be a bit more complicated if you've lost the key, but it's possible. The dealer will first need to read the VIN of the vehicle before requesting a replacement TWICE module and key blade that has the correct unique code. After that, they will be required to cut the replacement key and then program it with a brand new tool for programming called MDI.

Replacement Key Fob

The key fob is the piece that locks and unlocks your car, it's got an internal battery. They have a limited life span and will eventually die. This is a common problem that affects all cars, and the good news is that you can replace the batteries in a majority of key fobs and not have to replace the entire case. You can buy replacement fobs from Amazon that have all the electronics already installed, so you'll be able to just pop open the case and replace the old batteries. It is important to keep in mind that you'll need to take out the emergency key first, and you can accomplish this by inserting the small screwdriver flathead into the slot found in the middle of the case. The case should split when you rotate the screwdriver around it.

When you are ready to replace the keys, make sure you have a spare, as this will reduce your total cost by a significant amount. If you have a spare you can request that the dealer cut an entirely new key and then program it into your car, which is much cheaper than replacing the entire key fob.

It is possible to add a second key to your vehicle If you don't already have one, however it requires lots of research and work. Adding a second key costs around a hundred dollars and also requires programming of the car's computer. This can be accomplished by a professional, however it's a costly choice for the majority of owners.

Replacement Ignition

As opposed to the earlier Saab automobiles, the current saab 9-3 key not accepted contact service 9-3 models feature an extremely sophisticated alarm system that is based on a coded key. If you lose your primary key, it could be costly to replace it with another one since the car must be equipped with a specific computer and also be programmed to accept a brand new key. Dealers can even charge hundreds of dollars to program an additional key in the event that they are unable to complete the task.

If you've lost saab keys only one working key, a dealer will repair the computer in your car (known as the CIM or SAAB TWICE) to create the replacement, and will charge you the highest price for it. Instead, we can reprogram the EEPROM on your existing car computer to allow it to be programmed for a replacement key, which will save you more than 50% of what you'll pay at a dealership.

If you have owned a SAAB 9-3 for a long time, you know that the ignition keys aren't very durable. They can become extremely sticky, and the buttons are known to be removed from them every now and then which is why you should think about purchasing a new one if yours isn't working as it should. The good news is that replacing the ignition key isn't as difficult as it seems and can be done quickly with the proper tools.