See What Kia Picanto Key Fob Replacement Tricks The Celebs Are Using

How to Replace a kia picanto Key fob replacement (Glamorouslengths.com) Sportage Replacement Key

The key of a lot of kia car keys replacement models has an entry system that is keyless in. This key is similar to a remote control, and is exchangeable by a kia optima locked keys in car dealer.

Key fobs may stop working due to various reasons, such as a dead coin battery worn buttons, water damage, signal interference and a malfunctioning receiver module. Here are some tips to help you get your Kia sportage replacement key working for good.

How to replace the remote key or smart key?

The battery in your Kia's intelligent key will eventually need to be replaced, whether it's a remote, a push-to-start key or a regular key that is not equipped with a transponder. This is especially when your car displays a message telling you that the remote or smart keys are in poor condition.

It's quite simple to do. To replace the battery of the keyfob remove the mechanical key from the slot at the back of the fob. Then, pull the cover open. Inside the key fob there will be an incredibly small screw that holds the battery in the correct position. Using a small screwdriver, take the screw off and remove the battery that was in place. Insert the new battery and then close the slit on the key fob.

Test the key fob by pressing the lock and unlock buttons. If the doors unlock and lock exactly as you expect, then you're in good shape! You can now make use of the Kia's hands-free lock/unlock feature when your fingers start to get cold or you have to go on errands around Brandon.

Note: Some key fobs (transponder chip or smart keys) might require their programming completed. This requires a machine for programming that is only available to the locksmith in the automotive or dealer. Other keys (non-transponder metal keys) don't require programming. If your key has to be programmed again, you will need to be aware of the key code written on the tag of the key code and then record it in a safe location.

How do you replace the battery?

If your Kia key fob is not responding when you press the lock or unlock button on the fob, this is a sign that the battery needs to be replaced. A low battery may cause other issues, like the check engine light flashing or the engine not cranking correctly. Fortunately replacing the key fob battery is a simple DIY project that requires just a few basic tools.

Before you begin before beginning the process, ensure that your vehicle is turned off and that all doors are closed. Find the small metal or plastic piece at the bottom of your key fob and jiggle it until a metal key is released. The key can be inserted into the driver door handle to unlock your car.

To replace the key fob's battery, remove the cover on the rear and use a pry bar tool to remove the latch holding the black negative battery cable. Take the old battery out, and then align the replacement battery so that its "+" side is facing you and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position, avoiding excessive force to avoid bending or damaging the contacts on the metal.

After the new battery has been installed after which you turn the key fob off and on in the ignition until the door locks cycle. You can then test the Kia's key fob once more to ensure it's functioning properly.

How can you replace the smart key

You can have the standard keyfob or Smart Key based upon the model of Kia Sportage. The difference is that the smart key has an incredibly small key blade in it, whereas the standard key fob does not. Both kinds of key fobs contain batteries that will eventually have to be replaced. This is an easy process that takes just two minutes.

Before you begin it is important to ensure that you're on a level surface with sufficient lighting and that your Kia is turned off. Be aware that there are small parts inside the fob that can be snagged if not cautious.

The small release button is located on the lower backside. It's either a circular button or a rectangular slot. Once you press this mechanical key blade, it will be released and you can then open the key fob.

Once you have the key fob open then you can take out the old battery and replace it. The new battery should be a CR-2032, and can be purchased online or at a local auto parts store. After you're done, your key fob should allow you to lock, unlock, and start your vehicle even if it's not running.

How to replace a mechanical key

The Kia keyfob is a wonderful convenience which allows us to lock or unlock our car simply by pressing a button. Like any other device it may have issues at times. There are ways to address these issues and keep your key fobs functioning for a long time.

A low or dead battery is among the most common issues. This could cause the fob to stop working completely or even to stop working intermittently. If this is what you are experiencing, replace the battery with a new one.

If this doesn't solve the issue, use a standard flathead screwdriver to wedge the fob's plastic casing open. Be cautious not to damage any internal components or scratch the plastic. After the battery has been removed and replaced with a brand new battery.

Once the new battery is in, shut and open the doors with the mechanical key (every Kia fob comes with an emergency mechanical key that can you reprogram a kia key fob fit into the slot). Test the key fob to verify that it's functioning correctly. If the device not working, contact an authorized locksmith or dealer to help resolve the problem. Make sure they make you an emergency key that works for all trunk and door cylinders to avoid lockouts in the future.